SACCO CHURCH SUPPLY CATALOG 2022

Pews Bodies 23 17.0” 22.5” 4.875” 15.5” 14.375” 31.125” 33.0” 16.625” 1.125” 18.5” 12.5” 21.875” 4.875” 16.875” 31.25” 33.0” 16.625” 0.75” 18.5” 12.5” 22.875” 4.875” 16.875” 31.25” 33.0” 16.625” 0.75” Pew seats, backs and ends can be manufactured in various combinations to meet your specific requirements. We offer three basic pew body designs which follow: 101 Solid wood seat and back Seats are machined from 6/4 lumber (1.50” raw lumber thickness). Final thickness will be approximately 1-3/16”. Seats have a scooped out contoured area for comfort. Boards are glued up with tongue and groove construction. Seats are reinforced underneath with a 1.5” thickness x 2.5” height lateral brace. Backs are machined from 4/4 lumber (1” raw lumber thickness). Final thickness will be approzimately .75”. Boards are glued up with tongue and groove construction. The cap rail is fastened to the pew back with tongue and groove construction. 102 Padded seat and wood back Seats are manufactured with a .75” veneer core plywood base with solid poplar rails across the front and back for support and anchoring. Foam is 4” thickness with 2.6# density and 45 – 48# compression ratio. Many fabrics are available for a covering. Backs are machined from 4/4 lumber (1” raw lumber thickness). Final thickness will be approzimately .75”. Boards are glued up with tongue and groove construction. The cap rail is fastened to the pew back with tongue and groove construction. 103 Padded seat and back Seats are manufactured with a .75” veneer core plywood base with solid poplar rails across the front and back for support and anchoring. Foam is 4” thickness with 2.6# density and 45 – 48# compression ratio. Many fabrics are available for a covering. Backs are machined from 4/4 lumber (1” raw lumber thickness). Final thickness will be approzimately .75”. Boards are glued up with tongue and groove construction. The cap rail is fastened to the pew back with tongue and groove construction. The front of the pew back is covered with 1” foam and fabric which are removable for recovering at a future date. Pew Ends Pew ends are solid red oak, 2” thickness with butcher block or two-ply construction. Full pew ends have a separate 3” high foot glued, doweled and screwed to the pew end. This provides the support for anchoring to the floor. Pew ends are anchored to the floor with concealed fasteners, one per end. Two anchors are also available upon request. Pew supports are solid red oak, two-ply 1.5” thickness. Each panel is .75” thickness. Following are standard Woerner pew ends. Custom designs are available upon request. 556 Pew End 549 Pew End 526 Pew End 542 Pew End 530 Pew End 551 Pew End 576 Pew End 541 Pew End 584 Pew End 578 Pew End 546 Pew End 587 Pew End 577 Pew End 533 Pew End 585 Pew End 573 Pew End 564 Pew End 563 Pew End 532 Pew End 555 Pew End 571 Pew End 580 Pew End 539 Pew End 527 Pew End (Note: 585, 564, and 563 are also available without white finish) Church Furniture E7 Prices subject to change without notice. Pew Ends Pew ends are solid red ak, 2” thickness wit butcher block or two-ply c nstruction. Full pew e ds have s pa ate 3” high foot glued, doweled and screwed to the pew end. This provides the support for anchoring to the floor. Pew ends are anchored to the floor with concealed fasteners, one per end. Two anchors are also available upon request. Pew supports are solid red oak, two-ply 1.5” thickness. Each panel is .75” thickness. Following are standard Woerner pew ends. Custom designs are available upon request. 556 Pew End 549 Pew End 526 Pew End 542 Pew End 530 Pew End 551 Pew End 576 Pew End 541 Pew End 584 Pew End 578 Pew End 546 Pew End 587 Pew End 577 Pew End 533 Pew End 585 Pew End 573 Pew End 564 Pew End 563 Pew End 532 Pew End 555 Pew End 571 Pew End 580 Pew End 539 Pew End 527 Pew End (Note: 585, 564, and 563 are also available without white finish)

RkJQdWJsaXNoZXIy NDI2MjY1